Đánh giá: 32 Đánh giá: 9.0
DJ - Hãy là người Dj bạn luôn muốn trở thành với 3D Dj Music Mixer của chúng tôi trong một thế giới 3D
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Advance Property hau hau 9 43 2011-02-17T06:00:00Z 2011-02-17T07:03:00Z 7 1452 8279 rtk. 68 16 10167 9.3821 Advanced Properties Users can dynamically adjust the advanced properties in according to the operational environment and performance consideration. To adjust the setting of advanced property, please open Device Manager, expand the Network adapters tree list, select the "Realtek USB FE/GbE Family Controller", click mouse's right button, and launch the menu item of Properties..., the properties of "Realtek USB FE/GbE Family Controller" will prompt, select the property sheet of Advanced. NOTE: Advanced property settings are used for advanced users. For generic users, please use the default values. Improper setting of advanced properties will lead to failure connection or performance degradation. If such case happens, please refer this section to select the proper setting or restore to the default value. ARP Offload Auto response ARP request in sleep mode. Options Description Enabled Enable the capability of ARP Offload (default) Disabled Disable the capability of ARP Offload NOTE: (*) The default setting is dependent to products. Please refer the data sheet to set the feature. Energy Efficient Ethernet Energy Efficient Ethernet. The Realtek USB FE/GbE Family Controller can enter to or resume from power saving mode according to its loading. Options Description Enabled Enable the capability of EEE (default) Disabled Disable the capability of EEE NOTE: (*) The default setting is dependent to products. Please refer the data sheet to set the feature. Flow Control The Realtek USB FE/GbE Family Controller can temporarily stop to transmit packets while it receives flow control packet, or it can send the flow control packet to pause the transmitted side, in order to match the speed of transmitted and received side. flow control packet to pause the transmitted end toe Options Description Rx & Tx Enabled Enable the capability of flow control (default) Disabled Disable the capability of flow control IPv4 Checksum Offload Set the capability of IPv4 checksum by hardware Options Description Disable Disable the capability of IPv4 checksum by hardware Rx & Tx Enabled Enable the capability of IPv4 checksum both in Tx and Rx by hardware(default) Rx Enabled Enable the capability of IPv4 checksum only in Rx by hardware Tx Enabled Enable the capability of IPv4 checksum only in Tx by hardware Jumbo Frame The maximum transmit unit (MTU) of Ethernet is 1500 bytes. The jumbo frame is the frame whose length is greater than 1500 bytes. User can use this option to adjust the maximum transmit unit supported by Ethernet NIC. Options Description 2KB MTU Set the length of Jumbo Frame to 2K bytes. 3KB MTU Set the length of Jumbo Frame to 3K bytes. 4KB MTU Set the length of Jumbo Frame to 4K bytes. 5KB MTU Set the length of Jumbo Frame to 5K bytes. 6KB MTU Set the length of Jumbo Frame to 6K bytes. 7KB MTU Set the length of Jumbo Frame to 7K bytes. 8KB MTU Set the length of Jumbo Frame to 8K bytes. 9KB MTU Set the length of Jumbo Frame to 9K bytes. Disable Disable the capability of Jumbo Frame(default) NOTE: To enable the capability of Jumbo Frame, the other connected side is also need to enable the capability. Only GbE Family Controller supports Jumbo Frame. Large Send Offload v2(IPv4) Set the capability of TCP packet fragmentation by NIC hardware. Options Description Enabled Enable the capability of IPv4 packet fragmentation by NIC hardware (default) Disabled Disable the capability of IPv4 packet fragmentation by NIC hardware Large Send Offload v2(IPv6) Set the capability of IPv6 packet fragmentation by NIC hardware Options Description Enabled Enable the capability of IPv6 packet fragmentation by NIC hardware (default) Disabled Disable the capability of IPv6 packet fragmentation by NIC hardware Network Address Change the MAC address Default Value每Not present NS Offload Auto response NS request in sleep mode. Options Description Enabled Enable the capability of NS Offload (default) Disabled Disable the capability of NS Offload NOTE: (*) The default setting is dependent to products. Please refer the data sheet to set the feature. Priority & VLAN The information of IEEE 802.1Q/p is to indicate the packet's priority and the VLAN which it belonged. Set the option can enable the capability of priority transmit and VLAN tagging/de-tagging by NIC hardware. Options Description Disabled Disable the capabilities of priority and VLAN tagging/de-tagging Enabled Enable the capabilities of priority and VLAN tagging/de-tagging by hardware (default) Selective suspend Set the capability to enable NIC to suspend USB NIC port without affecting the operation of the other ports on the hub Options Description Enabled Enable the capability of selective suspend (default) Disabled Disable the capability of selective suspend Selective suspend idle timeout Set the idle timeout value for USB NIC selective suspend Options Description 1 ~ 60 While Selective suspend enabled, the idle timeout value used. 50 (default) Speed & Duplex Change the link speed and duplex mode Options Description Auto Negotiation Auto negotiation the supported link speed and duplex mode with connected device (default) 10 Mbps Half Duplex Set link speed and duplex mode to 10Mbps/Half Duplex 10 Mbps Full Duplex Set link speed and duplex mode to 10Mbps/Full Duplex 100 Mbps Half Duplex Set link speed and duplex mode to 100Mbps/Half Duplex 100 Mbps Full Duplex Set link speed and duplex mode to 100Mbps/Full Duplex 1.0 Gbps Full Duplex Set link speed and duplex mode to 1000Mbps/Full Duplex (*) NOTE: (*) Only GbE Family Controller supports 1.0 Gbps Full Duplex. TCP Checksum Offload (IPv4) Set the capability of TCP checksum by hardware (IPv4) Options Description Disable Disable the capability of TCP checksum by hardware(IPv4) Rx & Tx Enabled Enable the capability of TCP checksum both in Tx and Rx by hardware(IPv4)(default) Rx Enabled Enable the capability of TCP checksum only in Rx by hardware(IPv4) Tx Enabled Enable the capability of TCP checksum only in Tx by hardware(IPv4) TCP Checksum Offload (IPv6) Set the capability of TCP checksum by hardware(IPv6) Options Description Disable Disable the capability of TCP checksum by hardware(IPv6) Rx & Tx Enabled Enable the capability of TCP checksum both in Tx and Rx by hardware(IPv6)(default) Rx Enabled Enable the capability of TCP checksum only in Rx by hardware(IPv6) Tx Enabled Enable the capability of TCP checksum only in Tx by hardware(IPv6) UDP Checksum Offload (IPv4) Set the capability of UDP checksum by hardware (IPv4) Options Description Disable Disable the capability of UDP checksum by hardware(IPv4) Rx & Tx Enabled Enable the capability of UDP checksum both in Tx and Rx by hardware(IPv4)(default) Rx Enabled Enable the capability of UDP checksum only in Rx by hardware(IPv4) Tx Enabled Enable the capability of UDP checksum only in Tx by hardware(IPv4) UDP Checksum Offload (IPv6) Set the capability of UDP checksum by hardware(IPv6) Options Description Disable Disable the capability of UDP checksum by hardware(IPv6) Rx & Tx Enabled Enable the capability of UDP checksum both in Tx and Rx by hardware(IPv6)(default) Rx Enabled Enable the capability of UDP checksum only in Rx by hardware(IPv6) Tx Enabled Enable the capability of UDP checksum only in Tx by hardware(IPv6) Wake on link change Set the capability to enable NIC to wake up the system in sleep or hibernation state while ethernet link change Options Description Enabled Enable the capability of Wake on link change (default) Disabled Disable the capability of Wake on link change Wake on Magic Packet Set the capability to enable NIC to wake up the system in sleep or hibernation state while receiving magic packet Options Description Enabled Enable the capability of Wake on Magic Packet (default) Disabled Disable the capability of Wake on Magic Packet Wake on Pattern Match Set the capability to enable NIC to wake up the system in sleep or hibernation state while receiving the matched pattern Options Description Enabled Enable the capability of Wake on Pattern Match (default) Disabled Disable the capability of Wake on Pattern Match WOL & Shutdown Link Speed Set the link speed of NIC while the system is in sleep or hibernation state. Options Description 10 Mbps First Set the link speed 10 Mbps while system in sleep or hibernation state(default) 100 Mbps First Set the link speed 100 Mbps while system in sleep or hibernation state Not Speed DownSet the link speed 1000 Mbps while system in sleep or hibernation state
up